Refreshable Braille Display

Introduction

This project aims to develop a refreshable braille display to assist visually impaired individuals. The display will convert digital/printed text into braille in real-time, enabling users to read digital/printed content through the braille display.

Overview

The system captures images using the camera module and processes them through Tesseract OCR to extract textual content. The extracted text is then mapped to corresponding braille characters using a predefined dictionary. Each braille character's representation is translated into signals to control the position of braille dots via GPIO pins on the Raspberry Pi. The mechanical braille dot mechanism, driven by current flow through a copper wire wound around a plastic pipe with a nail and magnets, moves the dots up or down to form the braille characters. This process ensures that users can read text accurately and efficiently in braille format.

Key Features

Camera Integration: Incorporate a Raspberry Pi-compatible camera module to capture images of text.
OCR Processing: Use Tesseract OCR to extract text from captured images.
Braille Output: Display the converted text as braille characters on a refreshable braille display in real time.
Mechanical Braille Dots: Implement braille dots using copper wire wound around a plastic pipe with a nail inside, attached to magnets. The dots move up and down based on the current flow, providing feedback for braille characters.
Software Interface: Develop a user-friendly software interface to control the device.

Components Required

Component	Description
IC Chips	74HC595 (Shift Register) x4 L293D (H-Bridge) x6
Microcontroller	Raspberry Pi Zero 2W
Camera Module	Raspberry Pi camera module
SD card	Storage for Raspberry Pi 32GB
Power Supply	Rechargebale Batteries (3.2V, 6000mah 3C ) x2
Other Components	Insulated Copper Wire (50m) Iron Nails x12 Magnets x24 Hookup Wires Perf Board Push Buttons x3

Software Setup

Install Raspbian OS: Follow the official Raspberry Pi documentation to install Raspbian OS on the Raspberry Pi Zero 2W.
Enable Camera: Use raspi-config to enable the camera module.

Install Required Libraries:

sudo apt-get update
sudo apt-get install python3-rpi.gpio python3-picamera
sudo pip3 install rpicam2 pytesseract gpiozero pillow

Clone the Project Repository

git clone https://github.com/LokeshAravapalli/refreshable-braille-display.git
cd refreshable-braille-display

Table for Pin Connections

#(Note: VCC, GND, Enable Pins are not mentioned since they are the same for all components.)

Component	Pin Name	Connected to	Description
Camera Module	CSI Interface	CSI Interface	Camera connection
74HC595 Shift Register	SER (Serial Data)	GPIO 17	Serial Data
	SRCLK (Shift Clock)	GPIO 27	Shift Clock
	RCLK (Latch Clock)	GPIO 22	Latch Clock
	Output Bits	Inputs of H-Bridges	Input to control the H-Bridge

The shift registers will maintain the state of the braille dot. 2-bits from the shift register are given as input to the H-Bridge to control the H-Bridge.

Component	Pin Name	Connected to	Description
L293D H-Bridge	IN1	One of the output bits of the shift register	Input to control the current direction
	IN2	One of the output bits of the shift register	Input to control the current direction
	IN3	One of the output bits of the shift register	Input to control the current direction
	IN4	One of the output bits of the shift register	Input to control the current direction
	OUT1 && OUT2	2 terminals of an electromagnet	current direction controls the state of braille dot (up/down)
	OUT3 && OUT4	2 terminals of an electromagnet	current direction controls the state of braille dot (up/down)
	VSS2	Battery positive terminal	To provide current to the electromagnets

Each H bridge can control 2 electromagnets (braille dot) at a time. The shift registers maintain the state of the braille dot.

Component	Pin Name	Connected to	Description
Push Buttons	Button 1	GPIO 26 & other terminal to ground	User input button 1
	Button 2	GPIO 19 & other terminal to ground	User input button 2
	Button 3	GPIO 23 & other terminal to ground	User input button 3

Pinout Diagram

Note: VCC, GND, and Enable Pin (connected Vcc) are not drawn in the above picture for clarity.

Circuit and Code Explanation

When the push button is pressed, the camera captures the image and detects the text in it using the Pytesseract library. After text detection, we send output to shift registers in such a way their bits corresponds to each braille dot. We need 2 bits to control the direction of the current in H-Bridge. By giving using the shift register we maintain the state of bits and also control the current direction in the H-Bridge. Depending upon the direction of the current the dot either moves forward or backwards.

We have used 3 push buttons as input. 1 - To capture the image. 2 - To move to the next character. 3 - To move to the previous character.

Working Code

from picamera2 import Picamera2
from PIL import Image
import pytesseract
from gpiozero import LED, Button
import time

text = ""
letter1 = 0
letter2 = 1
num_of_characters = 2
camera = Picamera2()

def capture():
    global text
    config = camera.create_still_configuration()
    camera.configure(config)

    camera.start()
    camera.capture_file('image.jpg')
    camera.stop()
    print("Image Saved")
    text = pytesseract.image_to_string(Image.open('image.jpg'))
    print(text)


# Define GPIO pins
latchPin = 17
clockPin = 27
dataPin = 22

# Define input pins for buttons
button1Pin = 26
button2Pin = 19
button3Pin = 23

# Braille dictionary
brailleDictionary = {
    'A': 0b000001,
    'B': 0b000011,
    'C': 0b001001,
    'D': 0b011001,
    'E': 0b010001,
    'F': 0b001011,
    'G': 0b011011,
    'H': 0b010011,
    'I': 0b001010,
    'J': 0b011010,
    'K': 0b000101,
    'L': 0b000111,
    'M': 0b001101,
    'N': 0b011101,
    'O': 0b010101,
    'P': 0b001111,
    'Q': 0b011111,
    'R': 0b010111,
    'S': 0b001110,
    'T': 0b011110,
    'U': 0b100101,
    'V': 0b100111,
    'W': 0b111010,
    'X': 0b101101,
    'Y': 0b111101,
    'Z': 0b110101
}

# Initialize shift register data
d1 = 0
d2 = 0
d3 = 0
d4 = 0

# Initialize LEDs and buttons
latch = LED(latchPin)
clock = LED(clockPin)
data = LED(dataPin)
button1 = Button(button1Pin, pull_up=True)
button2 = Button(button2Pin, pull_up=True)
button3 = Button(button3Pin, pull_up=True)

def updateShiftRegisters():
    latch.off()
    shiftOut(data, clock, d4)
    shiftOut(data, clock, d3)
    shiftOut(data, clock, d2)
    shiftOut(data, clock, d1)
    latch.on()

def shiftOut(data, clock, val):
    for i in range(8):
        clock.off()
        data.value = (val & (1 << (7 - i))) != 0
        clock.on()

def getBraillePattern(letter):
    return brailleDictionary.get(letter.upper(), 0)

def createByte(b7, b6, b5, b4, b3, b2, b1, b0):
    return ((1 if b7 else 0) << 7) | ((1 if b6 else 0) << 6) | ((1 if b5 else 0) << 5) | ((1 if b4 else 0) << 4) | ((1 if b3 else 0) << 3) | ((1 if b2 else 0) << 2) | ((1 if b1 else 0) << 1) | (1 if b0 else 0)


def displayBraille(text):
    global d1, d2, d3, d4
    braillePattern1 = getBraillePattern(text[0])
    braillePattern2 = getBraillePattern(text[1])

    d1 = createByte(
        0,
        braillePattern1 & 0b010000,
        braillePattern1 & 0b000010,
        not (braillePattern1 & 0b000001),
        not (braillePattern1 & 0b001000),
        braillePattern1 & 0b001000,
        braillePattern1 & 0b000001,
        0
    )

    d2 = createByte(
        0,
        not (braillePattern1 & 0b000100),
        not (braillePattern1 & 0b100000),
        braillePattern1 & 0b100000,
        braillePattern1 & 0b000100,
        not (braillePattern1 & 0b000010),
        not (braillePattern1 & 0b010000),
        0
    )

    d3 = createByte(
        0,
        braillePattern2 & 0b010000,
        braillePattern2 & 0b000010,
        not (braillePattern2 & 0b000001),
        not (braillePattern2 & 0b001000),
        braillePattern2 & 0b001000,
        braillePattern2 & 0b000001,
        0
    )

    d4 = createByte(
        0,
        not (braillePattern2 & 0b000100),
        not (braillePattern2 & 0b100000),
        braillePattern2 & 0b100000,
        braillePattern2 & 0b000100,
        not (braillePattern2 & 0b000010),
        not (braillePattern2 & 0b010000),
        0
    )
    print(braillePattern2&0b100000)
    print(f'd1: {d1:08b}, d2: {d2:08b}, d3: {d3:08b}, d4: {d4:08b}')
    updateShiftRegisters()

def main():
    ## displayBraille("AA")
    global letter1, letter2, text, num_of_characters
    try:
        while True:
            #text = input()
            if button1.is_pressed:
                print("Button 1 pressed. Capturing Image")
                capture()
                letter1 = 0
                letter2 = 1
                displayBraille(text[letter1]+text[letter2])
            elif button2.is_pressed:
                print("Button 2 pressed. Displaying next letters")
                letter1 = letter1+num_of_characters
                letter2=letter2+num_of_characters
                displayBraille(text[letter1]+text[letter2])
            elif button3.is_pressed:
                print("Button 3 pressed. Displaying the previous letters")
                letter1 = letter1-num_of_characters
                letter2=letter2-num_of_characters
                displayBraille(text[letter1]+text[letter2])
            time.sleep(0.1)  # Check button state every 0.1 second
    except KeyboardInterrupt:
        pass

main()

Demo Video

https://github.com/LokeshAravapalli/refreshable-braille-display/tree/main/demo

Usage

After setting up the software and hardware, run the above code under - Working Code
Place the printed/ electronic text in front of the camera and press the button 1 to capture it. As soon as you press the first few letters of the text are displayed in braille.
Press button 2 to display the next characters in the text and button 3 to go back in the text.

Acknowledgements

Contributors

Thanks to the following people who have contributed to this project:

[Lokesh] - [GitHub Profile Link]
[Sujit] - [GitHub Profile Link]
[Lohitaksh] - [GitHub Profile Link]

Contact

Any queries, please contact us at [Lokeshkumar.Aravapalli@iiitb.ac.in] / [Sujit.Ghantasala@iiitb.ac.in] /[Lohitaksh.Maruvada@iiitb.ac.in].

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

README.md

README.md

Refreshable Braille Display

Table of Contents

Introduction

Overview

Key Features

Components Required

Software Setup

Table for Pin Connections

Pinout Diagram

Circuit and Code Explanation

Working Code

Demo Video

Usage

Acknowledgements

Contributors

Contact

Files

README.md

Latest commit

History

README.md

File metadata and controls

Refreshable Braille Display

Table of Contents

Introduction

Overview

Key Features

Components Required

Software Setup

Table for Pin Connections

Pinout Diagram

Circuit and Code Explanation

Working Code

Demo Video

Usage

Acknowledgements

Contributors

Contact