-
Notifications
You must be signed in to change notification settings - Fork 4
/
Copy pathprinter.cfg
130 lines (109 loc) · 2.99 KB
/
printer.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
[include hardware/btt_octopus_pin_aliases.cfg]
[include hardware/sb2040_pin_aliases.cfg]
[include hardware/resonance_tuning.cfg]
[include hardware/ab_steppers.cfg]
[include hardware/z_steppers.cfg]
[include hardware/extruder.cfg]
[include hardware/bed.cfg]
[include hardware/probe.cfg]
[include hardware/firmware_retraction.cfg]
[include hardware/sb_leds.cfg]
[include bed_mesh.cfg]
[include KAMP_Settings.cfg]
[include hardware/fans.cfg]
[include klicky/klicky-probe.cfg]
[include macros/z_calibration.cfg]
[include fluidd.cfg]
[include hardware/lights.cfg]
[include macros/nozzle_scrub.cfg]
[include macros/test_speed.cfg]
[include macros/chamber.cfg]
[include macros/homing.cfg]
[include macros/filament.cfg]
[include macros/spoolman.cfg]
# include print base macros
[include macros/print_base/print_start.cfg]
[include macros/print_base/print_end.cfg]
[include macros/print_base/park.cfg]
[include macros/pressure_advance.cfg]
#####################################################################
# MCU
#####################################################################
[mcu]
# serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_1E001B000E5053424E363620-if00
canbus_uuid: d5e039b242e0
[mcu SB]
canbus_uuid: 3282b8c50b03
##--------------------------------------------------------------------
[printer]
kinematics: corexy
max_velocity: 600
max_accel: 15000 #Max 4000
max_z_velocity: 50
max_z_accel: 350
square_corner_velocity: 5.0
[exclude_object]
# max_accel: 7000 # for resonance tuning
# max_accel_to_decel: 7000 # for resonance tuning
# enables echo like commands, useful for debugging
[respond]
[temperature_sensor rpi_cpu_temp]
sensor_type: temperature_host
[temperature_sensor SB2040]
sensor_type = ATC Semitec 104GT-2
sensor_pin = SB:TC
#####################################################################
# Homing and Gantry Adjustment Routines
#####################################################################
[idle_timeout]
timeout: 1800
[quad_gantry_level]
## Use QUAD_GANTRY_LEVEL to level a gantry.
## Gantry Corners for 350mm Build
gantry_corners:
-60,-10
410,420
# Probe points
points:
50,25
50,275
300,275
300,25
speed: 400
horizontal_move_z: 15
retries: 5
retry_tolerance: 0.01
max_adjust: 30
[filament_switch_sensor runout_sensor]
pause_on_runout: True
switch_pin: ESTOP7
#####################################################################
# Macros
#####################################################################
[delayed_gcode startup]
gcode:
STATUS_READY
initial_duration: 0.1
#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [stepper_z]
#*# position_endstop = 0.580
#*#
#*# [extruder]
#*# control = pid
#*# pid_kp = 20.621
#*# pid_ki = 1.676
#*# pid_kd = 63.410
#*#
#*# [heater_bed]
#*# control = pid
#*# pid_kp = 50.113
#*# pid_ki = 2.142
#*# pid_kd = 293.161
#*#
#*# [input_shaper]
#*# shaper_type_x = mzv
#*# shaper_freq_x = 56.4
#*# shaper_type_y = zv
#*# shaper_freq_y = 40.2