WagoMounts mod (VoronDesign#695)

* Add files via upload

* Update README.md

* Update README.md

* Add files via upload

* Add files via upload

* Delete Wago_221-41x_Extrusion_&_Thin_Din_Mount.f3d

* Delete Wago_221-41x_Extrusion_&_Thin_Din_Mount.step

* Delete Wago_3x_221-41x_Angled_Din_Rail_Mount.f3d

* Delete Wago_3x_221-41x_Angled_Din_Rail_Mount.step

* Create README.md

Author: LoganFraser

printer_mods/LoganFraser/README.md

@@ -0,0 +1 @@
+These mods are created by LoganFraser on Github - Logan#2225 on VoronDesign Discord

printer_mods/LoganFraser/WagoMounts/CAD/Wago_221-41x_Extrusion_&_Thin_Din_Mount.f3d

@@ -0,0 +1,11 @@
+This is a simple mount for attaching wago 221-41x to extrusion: by power inlet and under bed, or to Din Rails, for smaller builds.
+
+BOM - 2x M5-10mm bolts & 2x M5 T-nuts, Wago 221-41x
+
+![Image of WagoMounts-Extrusion&Din](WagoMounts-Extrusion&Din.png)
+
+This is a simple angled mount for wago 221-41x blocks in sets of 3 that mount to a din rail using the Trident power supply din rail clip. Original design by Socal3D on voron discord, I just cleaned up the design and added the mount. 
+
+BOM - 2x M3-8mm bolts, Wago 221-41x 
+
+![Image of WagoMount](WagoMounts.png)

printer_mods/LoganFraser/WagoMounts/CAD/Wago_221-41x_Extrusion_&_Thin_Din_Mount.step

@@ -234,6 +234,7 @@ like so:
 | | [V2.4 Bed Wiring Grommet](./LoCoCNC/wire_grommets) | Safely capture your bed wires thru the bottom panel |:x:|:x:|:heavy_check_mark:|:x:|
 |LoganFraser| [PiPlate](./LoganFraser/PiPlate) | PiPlate - Raspberry Pi3,4 mounting plate and Skirt Mod for V2.4/Trident |:x:|:x:|:heavy_check_mark:|:x:|:heavy_check_mark:|
 ||[Trident Inverted Electronics](./LoganFraser/TridentInvertedElectronics) | Flip the Trident electronics bay for top access.  |:x:|:x:|:x:|:x:|:heavy_check_mark:|
+||[WagoMounts](./LoganFraser/WagoMounts) | Wago Mounts for Din Rail or 2020 Extrusion mounting. |:grey_question:|:grey_question:|:heavy_check_mark:|:heavy_check_mark:|:heavy_check_mark:|
 |Long| [Mantis Dual 5015 Toolhead](./Long/Mantis_Dual_5015) | MGN12 Dual 5015 Toolhead for 2.4 & 1.8 |:x:|:heavy_check_mark:|:heavy_check_mark:|:x:|
 |Majarspeed| [Hartk board mount galileo](./Majarspeed/Hartk_Mount_Galileo) | It hangs stuff on your tool | :x: | :x: | :heavy_check_mark: | :x: |
 |MakeALeft| [Switchwire Clean Center Grill](./MakeALeft/Switchwire_Front_Grill) | Removed magnet holders on center panel for cleaner look | :x: | :x: | :x: | ✔️ | :x: