- nRF Connect SDK v2.8.0
- nRF Connect SDK v2.7.0
- nRF Connect SDK v2.6.0
- nRF Connect SDK v2.5.0
- nRF Connect SDK v2.4.0
- nRF Connect SDK v2.3.0
- nRF Connect SDK v2.2.0
- nRF Connect SDK v2.1.0
- nRF Connect SDK v2.0.0
- nRF Connect SDK v1.9.0
- nRF Connect SDK v1.8.0
- nRF Connect SDK v1.7.0
- nRF Connect SDK v1.6.0
- nRF Connect SDK v1.5.0
- nRF Connect SDK v1.4.0
- nRF Connect SDK v1.3.0
- nRF Connect SDK v1.2.0
- MPSL 0.5.0-1.prealpha
All the notable changes to this project are documented on this page.
- Removed support for running MPSL on the nRF54L15 PDK v0.7.0 and earlier. (DRGN-23325)
- Removed support for running MPSL on the Engineering A revision of the nRF54H20 SoC. (DRGN-23325)
- On nRF54L Series devices, the application now needs to implement :c:func:`mpsl_constlat_request_callback` and :c:func:`mpsl_lowpower_request_callback`. This is already added to the MPSL driver in the |NCS|. (DRGN-22562)
- Removed the :file:`mpsl_coex.h` API. (DRGN-22567)
- The timeslot implementation now starts
TIMER0a couple microseconds later. It now starts when theMPSL_TIMESLOT_SIGNAL_STARTcallback is given.
- Added production support for the nRF54L Series. (DRGN-23325)
- Added :c:func:`mpsl_fem_enable` to allow turning on the Front-End Module earlier than through a call to :c:func:`mpsl_fem_pa_configuration_set` (KRKNWK-19275). Added implementation of :c:func:`mpsl_fem_enable` for nRF2220 Front-End Module.
- Added the defines :c:macro:`MPSL_PPI_CHANNELS_USED_MASK`, :c:macro:`MPSL_DPPIC_CHANNELS_USED_MASK`, :c:macro:`MPSL_DPPIC10_CHANNELS_USED_MASK`, :c:macro:`MPSL_DPPIC20_CHANNELS_USED_MASK`, and :c:macro:`MPSL_DPPIC020_CHANNELS_USED_MASK`.
These represent the same resources as
MPSL_RESERVED_PPI_CHANNELS, but also specify the DPPI controller the channels belongs to. - Added the defines :c:macro:`MPSL_PPIB11_CHANNELS_USED_MASK`, :c:macro:`MPSL_PPIB21_CHANNELS_USED_MASK`, and :c:macro:`MPSL_IPCT130_CHANNELS_USED_MASK`. These represent the PPIB and IPCT resources used.
- Fixed a rare issue that could cause a scheduler assert if interrupts were disabled for a longer period of time (DRGN-24327). Note that disabling interrupts for a longer period of time is not allowed.
- The default bit width within timeslots for
TIMER0has been increased from 24 to 32 bits. The user may still configureTIMER0however they like during the timeslot. (DRGN-19050) - New FEM protocol APIs are provided to control the PA power, the previous APIs are removed.
This change does not affect applications developed in the |NCS| context.
:c:func:`mpsl_fem_pa_power_control_set` replaces :c:func:`mpsl_fem_pa_gain_set`.
:c:func:`mpsl_fem_caps_get` replaces :c:func:`mpsl_fem_pa_is_configured`.
The :c:struct:`mpsl_tx_power_split_t` structure contains the new field
fem_pa_power_controlto be used with the :c:func:`mpsl_fem_pa_power_control_set` function. The :c:type:`mpsl_fem_gain_t` type is deprecated, please use :c:type:`mpsl_fem_pa_power_control_t` type instead (KRKNWK-18729). - The FEM libraries for nRF2220 and nRF2240 no more link directly to the TWIM library.
- The TWI implementation now needs to be provided externally.
- The limitation that only the TWIM0 instance could be used for nRF2220 and nRF2240 devices is removed.
- :c:struct:`mpsl_fem_twi_if_t` replaces :c:struct:`mpsl_fem_twi_config_t`.
- The
twi_iffield replaces thetwi_configfield within :c:struct:`mpsl_fem_nrf2220_interface_config_t` and :c:struct:`mpsl_fem_nrf2240_interface_config_t` (KRKNWK-19010).
All the notable changes included in the |NCS| v2.6.0 release are documented in this section.
- The MPSL radio notification API has been removed. (DRGN-20447)
All the notable changes included in the |NCS| v2.5.0 release are documented in this section.
- FEM-related firmware is now built and deployed into separate libraries, one for each FEM implementation (such as
simple_gpio). - The :c:func:`mpsl_calibration_timer_handle` function must now be called when calibrating.
- Added :c:func:`mpsl_tx_power_dbm_to_radio_register_convert` to convert supported power in dBm to a register code for RADIO. (KRKNWK-17367)
- Added :c:func:`mpsl_clock_task_trigger_on_rtc_start_set` to trigger a PPI/DPPI task when the RTC starts. (DRGN-20396)
All the notable changes included in the |NCS| v2.4.0 release are documented in this section.
- Removed deprecated API for specifying the FEM pin configuration type associated with :c:macro:`MPSL_FEM_PIN_CFG_TYPE_PIN_PORT`. Only the :c:struct:`mpsl_fem_pin_t` configuration is supported as a FEM pin configuration now (KRKNWK-16496).
- Function for getting configuration of simple GPIO front-end module :c:func:`mpsl_fem_simple_gpio_interface_config_get`.
All the notable changes included in the |NCS| v2.3.0 release are documented in this section.
- The bool parameter
tx_power_ceilingto the external model used by the :c:func:`mpsl_fem_tx_power_split` function. When enabled, the function returns the ceiling value instead of the floor.
- Fixed a rare issue that could cause a scheduler assert if two roles were running (DRGN-18308).
- Fixed a rare issue that could cause an assert when requesting timeslots with type
MPSL_TIMESLOT_REQ_TYPE_EARLIEST(DRGN-18555).
All the notable changes included in the |NCS| v2.2.0 release are documented in this section.
- Fixed an issue where the scheduler could put events in the past (DRGN-17851, DRGN-18105).
All the notable changes included in the |NCS| v2.1.0 release are documented in this section.
- Support for the nRF21540 GPIO & SPI front-end module. SPI is used to set Tx gain of the nRF21540 in runtime. Support for this mode of operation for nRF21540 with Bluetooth LE is experimental.
- Support for adding an optional external model used to split the requested transmit power into components. This is then used by :c:func:`mpsl_fem_tx_power_split`. (KRKNWK-14464)
- An experimental version of a built-in nRF21540 GPIO & SPI front-end module compensation model.
- Removed the :c:func:`nrf_802154_fal_tx_power_get` function that is not used anymore by nRF 802.15.4 Radio Driver. (KRKNWK-14336)
- Changed :c:func:`mpsl_fem_tx_power_split` function so the :c:member:`mpsl_tx_power_split_t.radio_tx_power` field contains a value supported by the RADIO peripheral. Previously the value needed to be adjusted before applying to the RADIO peripheral. (KRKNWK-14323)
- Changed :c:struct:`mpsl_fem_gpiote_pin_config_t` and :c:struct:`mpsl_fem_gpio_pin_config_t` to require GPIO port address, port number and relative pin number instead of the absolute pin number. (KRKNWK-11891)
- Added production support for the 1-wire coexistence interface on the Nordic nRF52 Series. (DRGN-16439)
- Added :c:func:`mpsl_clock_hfclk_latency_set` which may be used to communicate the true high-frequency oscillator ramp-up time to MPSL. When not used, MPSL will make a worst-case assumption. (DRGN-13559)
- Added :c:func:`mpsl_tx_power_radio_supported_power_adjust` which lets users adjust the TX power to a value supported by the radio peripheral. (KRKNWK-14770)
- Changed :c:func:`mpsl_fem_tx_power_split` so that the returned front-end module gain component is a structure containing the gain in dB and a front-end module implementation specific private setting. Changed :c:func:`mpsl_fem_pa_gain_set` to accept this structure and apply the settings that it stores.
- Changed :c:func:`mpsl_fem_tx_power_split` to return the real achieved output power.
All the notable changes included in the |NCS| v2.0.0 release are documented in this section.
- Support for changing PA gain during runtime through MODE pin switching for the nRF21540 GPIO front-end module.
- Removed support for running MPSL on the nRF5340 PDK (DRGN-15174).
- Timeslot API values
MPSL_TIMESLOT_DISTANCE_MAX_USandMPSL_TIMESLOT_EARLIEST_TIMEOUT_MAX_USincreased to 256 seconds (DRGN-16800). - Extended :c:struct:`mpsl_fem_nrf21540_gpio_interface_config_t` with :c:member:`mpsl_fem_nrf21540_gpio_interface_config_t.mode_pin_config` and :c:member:`mpsl_fem_nrf21540_gpio_interface_config_t.fem_config.pa_gains_db`
- Fixed an issue where :c:func:`mpsl_uninit` would not disable the PPI channels used by MPSL (DRGN-16515).
- Fixed an issue where :c:func:`mpsl_init` would reject a certain clock configuration for no longer applicable legacy reasons (DRGN-16884).
- Fixed an issue where MPSL could assert when radio notifications on ACTIVE (:c:enumerator:`MPSL_RADIO_NOTIFICATION_TYPE_INT_ON_ACTIVE` or :c:enumerator:`MPSL_RADIO_NOTIFICATION_TYPE_INT_ON_BOTH`) were used (DRGN-16642).
- Fixed an issue where :c:func:`mpsl_uninit` would hang indefinitely when the RC oscillator was used as the Low Frequency Clock source (DRGN-16515).
- Fixed an issue where the High Frequency Clock would stay active if it was turned on between timing events. This could occur during Low Frequency Clock calibration when using the RC oscillator as the Low Frequency Clock source (DRGN-17014).
All the notable changes included in the |NCS| v1.9.0 release are documented in this section.
- Added a new header file :file:`mpsl_dppi_protocol_api.h` which exposes DPPI channels that have a fixed configuration during the lifetime of a radio event (DRGN-16308). This will facilitate debugging of protocol implementations. Currently these channels are guaranteed to be applied correctly for Bluetooth only.
All the notable changes included in the |NCS| v1.8.0 release are documented in this section.
- Added support for the Simple GPIO Front-End Module implementation on the nRF53 Series.
- Added support and separate documentation for Bluetooth External Radio Coexistence on the nRF52 Series (DRGN-11849).
- Added experimental support for the 1-wire coexistence interface on the nRF52 Series (DRGN-16439).
- References to Bluetooth support were moved away from :file:`projects/mpsl/doc/public/doc/cx.rst`. Its scope is now limited to IEEE 802.15.4 External Radio Coexistence.
- Fixed an issue where the current consumption in some cases was high after the end of a timeslot when using
MPSL_TIMESLOT_HFCLK_CFG_NO_GUARANTEE. Now the time from the request with typeMPSL_TIMESLOT_REQ_TYPE_EARLIESTuntil the event starts is in some cases increased (DRGN-16506).
All the notable changes included in the |NCS| v1.7.0 release are documented in this section.
- Added support for nRF21540 GPIO Front-End Module for nRF53 Series.
- Added a public interface for the radio coexistence protocol API (KRKNWK-7490). This public interface can be used to replace the example implementation of the radio coexistence with other implementations compliant with other Packet Traffic Arbitration (PTA) interfaces.
- The :file:`mpsl_fem_protocol_api.h` was moved from the :file:`include` directory to the :file:`include/protocol` directory (KRKNWK-10507).
- The start signal jitter for the timeslot API (
MPSL_TIMESLOT_START_JITTER_US) has been reduced to 1us. (DRGN-15842).
All the notable changes included in the nRF Connect SDK v1.6.0 release are documented in this section.
- Added an API to set and get a flag that determines whether to apply the DEVICE-CONFIG-254. The API user shall set the flag to desired value with :c:func:`mpsl_fem_device_config_254_shall_apply_set`. The protocol stacks' responsibility is to check the flag value using :c:func:`mpsl_fem_device_config_254_shall_apply_get` and apply the configuration when the flag value is true.
- Added support for the nRF5340 device, which was previously only supported for evaluation purposes (DRGN-8639).
- Added a function to the FEM protocol API to disable FEM when no radio activity is expected. This function is intended to reduce power consumption (KRKNWK-8842).
- Reserved TIMER1 for use by MPSL on nRF5340 (DRGN-15721).
- Fixed an issue where the clock configuration option :c:member:`mpsl_clock_lfclk_cfg_t.skip_wait_lfclk_started` did not work as expected with nRF5340 devices (DRGN-15223).
All the notable changes included in the nRF Connect SDK v1.5.0 release are documented in this section.
- Added a new signal to the MPSL timeslot:
MPSL_TIMESLOT_SIGNAL_OVERSTAYED. This signal is given to the application when a timeslot session is closed too late (DRGN-14677). - Added a new clock configuration option :c:member:`skip_wait_lfclk_started` in :c:struct:`mpsl_clock_lfclk_cfg_t`, which does not wait for the start of the low-frequency clock (DRGN-14204).
- Added macro MPSL_RESERVED_PPI_CHANNELS for a bit mask of (D)PPI channels reserved by MPSL (DRGN-13356).
- Fixed an issue where the low-frequency clock was configured incorrectly when the source configuration signal was set to either External Full swing or External Low swing (DRGN-15064).
- Fixed an issue where MPSL waited for the low-frequency clock to start even though it was configured not to wait for it (DRGN-15176).
All the notable changes included in the nRF Connect SDK v1.4.0 release are documented in this section.
- Changed the timeslot implementation to support up to 8 concurrent sessions (DRGN-13952).
It is now necessary to supply a timeslot context configuration using :c:func:`mpsl_timeslot_session_count_set`.
All timeslot APIs now take a
session_idas input. The session id is retrieved from :c:func:`mpsl_timeslot_session_open`. - Added an API to use Front-End Modules, like the nRF21540 GPIO or a simple GPIO, with the protocols and an API to configure them using the application. Only the nRF52 Series is supported.
- Fixed an issue where both the high-frequency clock and
TIMER0were not turned off during idle periods shorter than 9 ms (DRGN-14152). This increased the average power consumption. Such a case could occur when running a |BLE| connection with a connection interval of 7.5 ms.
See the :ref:`nrf:known_issues` page in |NCS| for the list of known issues and limitations for this release.
All the notable changes included in the nRF Connect SDK v1.3.0 release are documented in this section.
- Added API for fetching build revision information.
- Added API to set a TX Power envelope. Protocols using MPSL will limit their TX power to a value equal to, or lower than, the provided value.
- Added support for using a low-swing and full-swing LF clock.
- The support for integrating an 802.15.4 driver is now improved.
- Removed
MPSL_RADIO_NOTIFICATION_DISTANCE_425USand replaced it byMPSL_RADIO_NOTIFICATION_DISTANCE_420US. - On nRF53, the fix for Errata 16 is now applied.
- The scheduling overhead of a timeslot event is reduced.
- Fixed an issue on nRF53 where an assert could occur when using a timeslot.
All the notable changes included in the nRF Connect SDK v1.2.0 release are documented in this section.
- Added a library version with preliminary support for the nRF5340 device. The feature set is the same as in the MPSL library for nRF52. The following library has been added:
- Removed
_nrf52from the MPSL library file names. - Version numbers have been removed from the libraries.
- It is no longer allowed to call :c:func:`mpsl_init` if MPSL is already initialized.
- Clock configuration parameters for any stack that uses MPSL must be provided in :c:type:`mpsl_clock_lfclk_cfg_t` to :c:func:`mpsl_init`. This now also involves clock accuracy.
- Clock accuracy must be specified in parts per million (ppm).
- Renamed the MPSL clock API for the high-frequency and low-frequency clocks.
Initial release.
- Added the following MPSL library build variants:
hard-float/libmpsl_nrf52.asoft-float/libmpsl_nrf52.asoftfp-float/libmpsl_nrf52.a